OpenICE Community Support Forum

Welcome to the OpenICE community support forum. Use this forum for submitting bugs, asking for help, and solving problems you are having with OpenICE software. For ideas, general questions, and conversation please use the discussion forum.
0

How to add a new device

vchandak 21 hours ago in OpenICE 0

Hi Jeff


We are doing a POC and are planning to add a new device to OpenICE platform. Do you have any documentation that describe the standard process for adding a new device in terms of communication for initial handshake/protocol that needs to be implemented by this device. 


Regards
Vinod

device-adapter ICE OpenICE
+2
Searching answer

Philips Rev K Devices

NathanS 3 years ago in OpenICE • updated by ConfigRouter2 1 week ago 2
Hi,

I noticed that at least one other user has had difficulties using OpenICE with Philips Rev K devices.

I have been able to successfully connect to Philips MP70 and MP50 devices with Rev G (and I believe the MD PnP lab has Rev J).

I recently had the opportunity to test OpenICE on a Philips X2, Rev K.2. The X2 does not have a serial port, so I used the LAN port on the external battery pack, and ran the monitor in demo mode. OpenICE was able to successfully connect, and is able to extract the numerics alright, but there are problems with the waveforms. Initial waveforms appear in the GUI, but then stop (I was using version 0.6.3 of OpenICE).

The log file shows that the waveforms have "no new samples to emit", and that the physioId of one of the signals is being read in as 0. There is also a DDS error indicating that the participant information was not available for device identity publication (see log file excerpt below).

Initially, and occasionally afterwards, there is valid waveform data in the sample array updates (viewed in the debugger). However, very quickly after starting, the updates start coming back empty. I have written code to export the numerics/waveform data to csv; the numerics data is written fine, but not even the first packet of waveform data is recorded.

I remember seeing the flags INVALID | QUESTIONABLE | UNAVAILABLE in the debugger for the MeasurementState of SampleArrayObservedValue objects (with physioId = 0).

I later tried testing on an X2 with rev J, and the software worked without problems. So there does seem to be a problem with rev K (and possibly newer) devices.

I have compared the export interface manuals for both Rev H and Rev K, and the differences between the two appear to be minimal (a few new objects have been defined).

Unfortunately I have had to send back the X2 rev K I had on loan, so I am unable to do much more hands-on troubleshooting myself at the moment. I do still have log files, and I did spend some time with a java debugger stepping through the code (mostly in AbstractDemoIntellivue and AbstractDevice), so I might be able to answer some questions... But hopefully the above information will be helpful when one of you needs to troubleshoot rev K or higher devices!

Regards,
Nathan

---------------------------------------------------

2015-05-26 14:38:23,524 | WARN | Bean with key 'timeManager' has been registered as an MBean but has no exposed attributes or operations | org.springframework.jmx.export.MBeanExporter | JavaFX Application Thread
2015-05-26 14:38:23,576 | ERROR | [D0000|Reader(80000807)|T=DeviceIdentity|GET_MATCHED Participant DATA]DDS_DataReader_get_matched_publication_participant_data:ERROR: Failed to get discovered_participant_data | com.rti.dds | EventLoopHandler
2015-05-26 14:38:23,576 | WARN | Unable to get participant information for DeviceIdentity publication | org.mdpnp.apps.testapp.DeviceListModelImpl | EventLoopHandler
2015-05-26 14:38:23,617 | INFO | Connecting to >126.3.145.100< | org.mdpnp.devices.DeviceDriverProvider$SpringLoadedDriver | Thread-15
2015-05-26 14:38:23,849 | INFO | Start emit fast data for period 2000ms | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | Network Loop
2015-05-26 14:38:24,375 | INFO | ProductionSpecification | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:24,376 | INFO | [[specType=SERIAL_NUMBER,componentId=ID_COMP_PRODUCT,prodSpec=DE037A8036], [specType=PART_NUMBER,componentId=ID_COMP_PRODUCT,prodSpec=M3002A], [specType=PART_NUMBER,componentId=ID_COMP_APPL_SW,prodSpec=S-M8102-1501A ], [specType=SW_REVISION,componentId=ID_COMP_APPL_SW,prodSpec=K.21.39 ], [specType=PART_NUMBER,componentId=ID_COMP_CONFIG,prodSpec=S-M8102-1401A ], [specType=SW_REVISION,componentId=ID_COMP_CONFIG,prodSpec=K.21.39 ], [specType=PART_NUMBER,componentId=ID_COMP_BOOT,prodSpec=S-M8000-1301A ], [specType=SW_REVISION,componentId=ID_COMP_BOOT,prodSpec=A.16.24]] | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:24,378 | ERROR | [D0000|Reader(80000807)|T=DeviceIdentity|GET_MATCHED Participant DATA]DDS_DataReader_get_matched_publication_participant_data:ERROR: Failed to get discovered_participant_data | com.rti.dds | EventLoopHandler
2015-05-26 14:38:24,379 | WARN | Unable to get participant information for DeviceIdentity publication | org.mdpnp.apps.testapp.DeviceListModelImpl | EventLoopHandler
2015-05-26 14:38:24,382 | ERROR | [D0000|Reader(80000807)|T=DeviceIdentity|GET_MATCHED Participant DATA]DDS_DataReader_get_matched_publication_participant_data:ERROR: Failed to get discovered_participant_data | com.rti.dds | EventLoopHandler
2015-05-26 14:38:24,382 | WARN | Unable to get participant information for DeviceIdentity publication | org.mdpnp.apps.testapp.DeviceListModelImpl | EventLoopHandler
2015-05-26 14:38:27,442 | WARN | No ObservedValue for 0 | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:27,443 | WARN | No ObservedValue for 0 | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:27,444 | WARN | No ObservedValue for 0 | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:27,469 | WARN | No SampleArraySpecification or RelativeTime for handle=2006 rt=null sas=null sar=null unitCode=null | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:28,002 | WARN | MDC_IMPED_TTHOR 1827 will repeat 109 old samples to make up a shortfall | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:28,002 | WARN | MDC_IMPED_TTHOR 1827 filling in 109 zeros; this should not continue happening | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:28,006 | WARN | MDC_ECG_LEAD_III 1817 will repeat 872 old samples to make up a shortfall | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:28,006 | WARN | MDC_ECG_LEAD_III 1817 filling in 872 zeros; this should not continue happening | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:28,020 | WARN | MDC_ECG_LEAD_II 1817 will repeat 872 old samples to make up a shortfall | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:28,020 | WARN | MDC_ECG_LEAD_II 1817 filling in 872 zeros; this should not continue happening | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:28,034 | WARN | MDC_ECG_LEAD_I 1817 will repeat 872 old samples to make up a shortfall | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:28,034 | WARN | MDC_ECG_LEAD_I 1817 filling in 872 zeros; this should not continue happening | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:28,464 | WARN | No ObservedValue for 0 | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:28,466 | WARN | No ObservedValue for 0 | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
...
org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:30,001 | WARN | MDC_IMPED_TTHOR 1827 no new samples to emit | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:30,002 | WARN | MDC_ECG_LEAD_III 1817 no new samples to emit | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:30,002 | WARN | MDC_ECG_LEAD_II 1817 no new samples to emit | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:30,002 | WARN | MDC_ECG_LEAD_I 1817 no new samples to emit | org.mdpnp.devices.philips.intellivue.DemoEthernetIntellivue | taskExecutor-1
2015-05-26 14:38:30,516 | WARN | No ObservedValue for 0 | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:30,518 | WARN | No ObservedValue for 0 | org.mdpnp.devices.philips.intellivue.AbstractDemoIntellivue$IntellivueExt | Network Loop
2015-05-26 14:38:30,518 | WARN | No ObservedValue for 0 |
...
2015-05-26 14:38:33,593 | ERROR | [D0000|Reader(80000807)|T=DeviceIdentity|GET_MATCHED Participant DATA]DDS_DataReader_get_matched_publication_participant_data:ERROR: Failed to get discovered_participant_data | com.rti.dds | EventLoopHandler
2015-05-26 14:38:33,593 | WARN | Unable to get participant information for DeviceIdentity publication | org.mdpnp.apps.testapp.DeviceListModelImpl | EventLoopHandler


-----------------------------------------------



OpenICE demo-apps device-adapter
+1
Under review

TimeSync BBB rev C with time server on local network.

Vasanth Jaisingh 3 years ago • updated by ConfigRouter1 1 week ago 1
Hi,

How do I time sync my BBB with time server present on my local network.
At times, time also sets back to Mar 1 2015 after reboots.

Please advise.

Regards
Answer
Jeff Peterson 3 years ago
Hi Vasanth,

Beaglebones Blacks do not have a real time clock and thus require time synchronization after each boot. We have taken several approaches to time synchronization over the years. The simplest approach is to give your Beaglebones access to the Internet, specifically pool.ntp.org. Our current approach is to use our Cisco router as a NTP time server. To do this, we had to configure DHCP Option 42 in the DHCP pool configuration to the address of the router and point the router to the US NTP pool. Neither of these options require edits to the Beaglebone's NTP configuration file at /etc/ntp.conf although your eventual solution may be different.

I would suggest searching Beaglebone or Linux forums for time synchronization options and setup assistance. I've copied a link below that might be a good place to start.
http://derekmolloy.ie/automatically-setting-the-beaglebone-black-time-using-ntp/

Thanks,
Jeff
0
Answered

Write data into a medical device

srav0508 3 months ago in OpenICE • updated by Dylan Bagshaw 1 week ago 1

Hi,

From the documentation provided in website, I see that we can read data from medical devices such as patient monitors and ventilators. 

Using Open ICE and Beaglebones, can we write some data (say list of values from a text file) to a certain parameter  (say pressure waveform) in ventilator?

The application is to simulate real time data in medical device and test how it behaves.

Please suggest.

OpenICE
Answer
Dylan Bagshaw 1 week ago

Very few medical devices accept data input of any kind. We haven't  come across any medical devices in which you can change the output in the way you desire. OpenICE does have some simulated devices built in to the software, unfortunately, no ventilator.

0
Fixed

artifactiory not accessibile

geovannio vinhas 2 months ago in OpenICE • updated by Dylan Bagshaw 1 week ago 1

Hello,

I am trying to build the mdpn repo but it looks like https://build.openice.info/artifactory is down. 

This are the error i get:

* What went wrong: A problem occurred evaluating project ':data-types:x73-idl-rti-dds'. > Could not resolve all dependencies for configuration ':data-types:x73-idl-rti-dds:rtiddsgen'.    > Could not resolve org.anarres:cpp-bin:1.2.8-SNAPSHOT.      Required by:          org.mdpnp:x73-idl-rti-dds:0.6.3-SNAPSHOT       > Unable to load Maven meta-data from https://build.openice.info/artifactory/libs-snapshot/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml.          > Could not GET 'https://build.openice.info/artifactory/libs-snapshot/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml'.             > peer not authenticated       > Unable to load Maven meta-data from https://build.openice.info/artifactory/libs-release/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml.          > Could not GET 'https://build.openice.info/artifactory/libs-release/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml'.             > peer not authenticated       > Unable to load Maven meta-data from https://build.openice.info/artifactory/remote-repos/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml.          > Could not GET 'https://build.openice.info/artifactory/remote-repos/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml'.             > peer not authenticated

OpenICE
Answer
Dylan Bagshaw 1 week ago

Sorry for the inconvenience. Hopefully your issue has been solved. Those builds are hosted on a server in our lab, if you ever have an issue with it not building correctly due to an error like that, try waiting a little while and building again. Alternatively, if you've previously built the project you can run with the argument < --offline > (without the <>) and it will build with the files saved on your system.

0
Answered

Build OpenICE from source

Rado 3 years ago in OpenICE • updated by VersionWeekly 1 month ago 8
Hello,

We are trying to use openICE for integration with several different medical devices at the University of Pennsylvania and the surrounding hospitals. We are able to use the demo app that is pre-built but we are having trouble building the code from source.

We have tested this on Windows, Mac and Ubuntu and get to the same stage. We are able to import the project using the eclipse plugin for gradle but there are some bits that don't compile. In particular, the main problem is that the ice environment that is defined in a few idl files is not correctly recognized by the java files (so the most common error is "ice cannot be resolved to a type"). As far as I understand, some java code has to be generated by these specifications but we cannot get eclipse to do it.

Is there some other pluging that we need to install? Or do you think there is some other problem?

Thanks,
Rado
OpenICE
0
Answered

How can I email support requests?

Dave 3 years ago • updated by ConfigRouter 1 month ago 4
I'd like to email in questions. Is this supported?
0

Comparison between MDPnP vs SCOT vs OR.NET

dkotian95 1 month ago 0

We are trying to evaluate Medical devices to make it compliant to MDPnP or OR,NET or SCOT, is there any comparison done to these 3 technology.


I am new to these and even MDPnP, what would be the starting point for MDPnP and is there any documented steps what needs to be done to make our Medical devices compliant with MDPnP.

Currently, I am just looking at the feasibility only on paper for our device.



Is there any membership forum paid or free to participate and understand closely with the architects/Leads developing MDPnP?


Please let us know your views


Regards

Deepak


0

OpenICE can't get data from MX800

Jason Norman 2 months ago in OpenICE 0

I have OpenICE working correctly with a Philips MP70, but I need it to work with the MX800.


Following the exact same process for connection with the MX800, I wind up with the unplugged "no data" indicator on my MX800 in the OpenICE devices list.


One thing that stands out to me is the difference between the MIB/RS232 port on the backs of the monitors. The MP70 has two separate ports, I assume one for input and the other for output. The OpenICE documentation suggests using the port with the arrow pointing out of the circle, like this: 


O->


The MIB/RS232 port on the back of my MX800 only has one port, and it has a double arrow indicator, like this:


O<->


So I am wondering if this port is configurable as either input or output, and if that is possibly my problem. Does anyone here have any input on this issue?


Thanks.

0

Unable to connect BBB with philips MP70 with OpenICE

Unnikuttan V V 2 months ago in OpenICE • updated 2 months ago 1

Hi,

I am trying to interface Philips IntelliVue MP70 with OpenICE using the steps given in https://www.openice.info/docs/4_device-adapter-setup.html. After everything is done the application is

+2

Build OpenICE fom github failed

Hank Hung 4 months ago in OpenICE • updated by geovannio vinhas 2 months ago 1

Hello,


When I build mdpnp source code form github, I encounter some issue.

It print some error, look like the artifactory files not exist?



A problem occurred evaluating project ':data-types:x73-idl-rti-dds'.

> Could not resolve all dependencies for configuration ':data-types:x73-idl-rti-dds:rtiddsgen'.
   > Could not resolve org.anarres:cpp-bin:1.2.8-SNAPSHOT.
     Required by:
         org.mdpnp:x73-idl-rti-dds:0.6.3-SNAPSHOT
      > Unable to load Maven meta-data from https://build.openice.info/artifactory/libs-snapshot/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml.
         > Could not GET 'https://build.openice.info/artifactory/libs-snapshot/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml'.
            > peer not authenticated
      > Unable to load Maven meta-data from https://build.openice.info/artifactory/libs-release/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml.
         > Could not GET 'https://build.openice.info/artifactory/libs-release/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml'.
            > peer not authenticated
      > Unable to load Maven meta-data from https://build.openice.info/artifactory/remote-repos/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml.
         > Could not GET 'https://build.openice.info/artifactory/remote-repos/org/anarres/cpp-bin/1.2.8-SNAPSHOT/maven-metadata.xml'.
            > peer not authenticated



Please help me solve it. Thanks.



Hank

DDS OpenICE
0

Connecting Evita 4 via serial DB9

Tarun 2 years ago in OpenICE • updated by brilkov 3 months ago 1

Hi,


I am currently connecting Evita4 with laptop.

my connection is as follows:

evita->serial to usb connector ->laptop USB. I have crossed pin2 and 3(rx,tx) from evita.


Then i launch openice device configurator and add evita4 via serial. I tried all baudrates and parities. The device connector goes into endless connecting loop. However, I can use realterm to transmit basic commads and get replied.


Can you please provide steps to connect Evita 4.


Regards,

Tarun

0

Connecting to Philips IntellieVue over LAN: Stuck on Negotiating (Requesting association)

Luke Fletcher 2 years ago in OpenICE • updated by Srikanth Muthya 4 months ago 10

Hi


Firstly, thanks to the OpenICE community for supporting this amazing project.


I'm trying to use OpenICE (v0.6.3) to connect to Philips IntelliVue monitors over LAN. My computer (OSX 10.11.3) is connected to the same internal ICU LAN network the monitors are connected to. I have an IP address, and I can ping the monitors. However, when I connect to the monitor IP address, the connection status in OpenICE is stuck on "Negotiating (Requesting association)". This is true of any monitor I attempt to connect to in the unit. Just to be explicitly clear, I am not using serial/RJ45/RS232. Just LAN.


I am able to connect to the monitor just fine when the monitor is connected to an isolated network. I believe the issue may be that the monitors are already connected with the central Philips server. Can IntelliVue monitors connect to both the Philips server and OpenICE simultaneously? Is there any other reason that could explain this behaviour?


Kind regards


Luke Fletcher

OpenICE
0
Under review

supported devices

Alistair MacDonald 3 years ago in OpenICE • updated by Anna 4 months ago 10
Hello Jeff. We're in Missoula working on an OR music volume controller project using OpenICE and Philips MP70 monitors. Do you know what's in the queue for drivers for the newest monitors such as Spacelabs (Xpression), Nihon Kohden BSM 6000 series, Mindray DPM, GE Carescape, Drager Perseus. I know some communication protocols are openly available for NK, Mindray and GE, but wasn't sure if and when they would make their way into OpenICE.
-Alistair MacDonald
0

Puritan Bennet 840 Serial Port connection

jbarrueco 4 months ago in OpenICE 0

I'm having problems to connect PB 840 to a MacBook. I'm using a serial to USB cable. Despite I installed OpenICE and Java, the Device Adapter does not recognizes it, just shows bluetooth port of the Mac. I installed another app called "Serial" and it reads the serial port but I want realtime, high frecuency data to build waveforms and make lung mechanics analysis. What I'm doing wrong?